Sanding, sanding, sanding

Hi,  Started sanding dinette table.  Had been covered with woodblock look contact paper.  Took most of the old varnish with it when removed.  Has lots of old scratches in it and goo on edges from the contact paper.  Leg will have to be remade, it is splitting at the bottom.  Will need another sanding session (hands can only take so much of the sander) to get it to finish ready.  Sanded and varnished fridge front insert.  Looking like rain that made me stop working outside.  Undid some of the exterior screws of  right rear corner trim.  Not much caulk or putty under it.  Will have to remove both trim pieces and reputty tape them.  Going to rv parts supplier Sun.  Hope to get a lot of things I need. :)  Bye for today.

Painting and Varnishing begins

Hi,  Got first coat of varnish and paint on first dinette bench.  Looks so good.  Love how varnish brings out the beauty in wood.  Other bench, got two screws out will have to cut out other 2.  Undid old wiring.  Will be able to keep water tank since it is plastic.  Little pump reuseablity to be determined since it is 12v. 

Sanding started

Hi,  Started sanding and finishing the first dinette bench.  Wonderful to do something constructive rather than deconstructive.  Made a decision too, not converting to 12v.  We are going to rewire and add junction boxes etc., for safety.  Ray checked out the fridge it did not initially start.  Needs his meters and things to do full check of it.  Fun is happening.  Bye Bye.

More Demo news

Hi,  Took a couple of days off.  Other things in life had to take precedence.  Started removing old floor tile. Really hate floor scraping.  Do it in little bits it will eventually get done.  Removed old gas lights and half the dinette.  Will prime and paint the benches and the table.  Table needs a new leg.  Made out of plywood and it's split at the bottom.  Tiny bit of plywood rot by door.  Glad to see how little damage was there.  Door will need to come out to refinish the correct way, rusting through current paint.  Back door will need same treatment.  Was a little discouraged last night, more work needed than anticipated.  But it deserves to be fixed up correctly since it is basically very solid.  Just needed better care through the years.  One day at a time sure covers a lot of things.  Bye Bye for now.

Demo Day 3

Yesterday the damaged ceiling panel came down.  Looks like something punctured the roof, possibly a branch.  Will need to post a picture. This was patched with a piece of metal and thick black stuff that has grown hard. Will need to take the good part of this section down to have a nailing surface for the new panel.  Priced birch plywood vs. decorative panel.  Prices about the same.  Been on line pricing other replacement and roof sealing products.  Friend told me of a supplier south of us that sells RV supplies inexpensively.  May need to make a day trip down there. Probably taking today off, body needs a break and now have a cold.  Bye Bye

Demo day 2

More ecivation today.  Found source of some of the wet.  Also discovered under the floor is asbestos board.  Some of it was rotted in the back corners, rest seems in good shape so I don't need to disturb it.  Might be able to undercoat it somehow. More tomorrow.

Demo Started!

Started demolition today.  After removing screws for hinges of the upper bed, Ray had to get it out of trailer for me.  I was really heavy because it was an old tongue and groove door.  Obviously not original equipment.  Next removed lower bed deck.  That wasn't original either.  Started removing the panelling at the back corners.  A lot of moisture damage, even still wet.  Have a feeling the back windows may need to be removed.  That will depend on how much internal wall damage there is after removing all the panelling under the windows.  Floor has to have damage too in those corners. Think old tail lights leaked.  Still another source from ceiling on down in the one corner.  Not discouraged, all fixable. Bye for now.